It is important to ensure that your wall clock is properly wound up. When your battery-operated wall clock stops altogether and doesn’t work, it typically results from loss of charge on one or both of the batteries. It may happen that the clock’s battery has lost sufficient charge or the acid in the battery has leaked, thereby causing corrosion.
You need to check whether the issue lies with your clock. It has been seen that the internal mechanisms like springs, cogs, and other clock movement remains unaffected and are also not faulty most of the time. Clocks need routine maintenance to prevent stopping at the same time.
Why does my wall clock keep stopping at the same time? Your wall clock keeps stopping at the same time because the clock pendulum stops swinging after moving because your wall click case is now leaning at a different angle slightly than when it was at an earlier location.
Where Should I Fix My Clock?
As per Vastu guidelines, to keep your wall clocks in your office or home in the right direction, you can place them eastward; however, don’t try to display the clock’s metal body in this particular direction. Therefore, the west direction is the best place where you can keep your metal clock. It is important to keep the clock in the working direction and hang the clock inside your house.
Different Reasons Why The Clock Is Stopping At The Same Time
- Battery pips are not enough in length
- Dirty or loose battery connection
- Low battery
- Grime has accumulated in the clock mechanism and causes excessive friction
What Should I Do If My Wall Clock Doesn’t Work?
Have a look at minute hands and hour hands to ensure that both hands are not coming into contact. If they are in contact, press the clock’s hour hand gently towards the clock dual slightly to ensure that the hands are not touching the dial. If they are still in contact, bend the minute hand slightly towards you to make a clearance space.
This is why the clock pendulum stops swinging after moving because your wall clock case leans at a different angle slightly. If you find the clock loose, you can speed up your wall clock by tightening the nut. This will raise the Bob and make the pendulum length shorter, and as a result, the hour clock will work faster.
Why Don’t The Hands Of My Wall Clock Move?
If you see that the hands of your clock are not moving, then this can be because the center hex has become too tight. Loosen the center hex for about a quarter turn. If you see the second clock hand is also not moving, give a flick to it in the correct direction. If you don’t see the clock move again, put the batteries in the back for some seconds and later return to normal.
Why Does The Pendulum Of My Wall Clock Stop Working?
A pendulum in a clock is an object that hangs and keeps swinging back and forth from a fixed point due to the gravitational action. The pendulum keeps swinging, moving forth and back unless friction occurs between the attachment points and chains and between the swing and the air. Therefore the pendulum slows down abs and eventually stops working at the same time.
Measures Taken When Your Wall Clock Keeps Stopping At The Same Time
Technological advancement has created wall clocks that are easy to maintain and are quite efficient. One common clock available in the market is a quartz clock. There require electrical currents and quartz crystals to keep intact the time.
This clock is often easy to maintain and just needs the replacement of batteries when they don’t work. If the clock doesn’t work even after using new batteries, you must check to ensure that the wall clock’s hands don’t hit other parts of the wall clock.
1. Replacement of battery
The battery compartment must be opened, which lies on the back of your wall clock. The battery is housed in a small black box. Remove old batteries by using your fingers and prying up the battery ends. You must check the battery’s condition with a universal tester for the battery.
You need to check your wall clock’s batteries for power in the back. If you see that the batteries are corroded or have become bad, then replace them. If you see that the clock’s minute hand is running either too slow or too fast, then set the right time. If you set your wall clock by the hour hand, it can make the clock run erratically.
2. Clean The Battery Terminals
You can use ethanol or isopropyl alcohol. To stop your wall clock from stopping every time at the same time, then rub alcohol on the cotton bud and clean the battery terminals and connection. Your wall clock is stopping at the same time, maybe because the electrical springy strips and even the ends of the clock battery have become oxidized.
You can see this oxidization in the form of a green or grey coating. You can easily remove it by using wool. If the clock’s battery has leaked and has left a white deposit, you can use vinegar and neutralize it.
It becomes crucial to ensure that the battery terminals are not wet when you insert a new battery. Many times, the battery’s terminal pips can be a bit shorter. You can bend the positive terminal strip in your wall clock slightly. You can use a clean towel or cloth and gently dry off the battery terminals. You can also use an air dryer to dry the terminals.
3. Check Your Clock Hands
The next important thing to notice is ensuring that the clock’s hands are not rubbing or creating friction over the clock‘s face.
4. Further Steps
If following the above steps doesn’t make your wall clock run, this can be due to grime in the cogs and on the axles. There can be a possibility of mildew and dust getting inside. Therefore, you need to do a bit of cleaning stuff.
Your clock consists of the solenoid, which produces a small twisting force or torque to turn the rotator. If grime accumulates on the rotator’s pins, it can produce much friction and stop the clock from turning.
A battery-operated wall clock is known to stop at the same time because of issues caused by one or more clock batteries, leaking of battery acid, and low charge of your battery. Follow these measures to prevent your wall clock from stopping at the same time.